Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths who have the right equipment and know-how. They can design and program keys quicker and more efficiently than a dealership.
If your key fob stopped locking or unlocking your doors it is likely due to a dead battery in the coin. However, there are other possibilities that the key is malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as making it impossible to start the engine. If this is the case, you'll have to utilize the backup starting method that's described in the owner's manual to your vehicle.
The spark plugs can also be worn out. The spark plugs are responsible for instigating the fuel that powers the engine. They have a limited life span. They'll eventually fail in the event that they aren't utilized enough.
Luckily, there's an easy solution for this issue. The best thing to do is to test the voltage of your car battery with a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. If the battery is corroded it is crucial to clean its contacts. You can do this by lifting the rubber covers that cover the two terminals of the battery and using wire brushes to clean any corroded areas of the battery. Then, reconnect the cables for the positive and negative poles.
Water Damage
If your 208 won't start and the battery is not flat then you should check that the spark plugs are in good working order. You may find that they're dirty and do not spark. This can be easily corrected by cleaning the spark plugs in an workshop.
Peugeot automobiles use a key with a transponder compatible with the immobiliser. This guarantees that only the right key is able to start the engine. If the chip inside the Peugeot key is damaged, it won't transmit the proper signal to the vehicle.
Water damage is the most common cause of this problem. This is a typical issue in more cold climates where the car is exposed to rain or snow. If this is the case, call a reputable auto locksmith who will have all of the equipment and tools needed to reprogram the new key. They also have the most up-to-date technological know-how and the equipment required to make a Peugeot 208 smart key. peugeot van key replacement G28 should take no more than 15 minutes.
Faulty Battery Contacts
Peugeot changed from the carbon-encased transponder chips to a new type of chip that relies on electronic components on a circuit board. The new system is great when it's new, but the circuit boards degrade over time and stop working properly.
This could prevent the immobiliser chip activating the immobiliser chip, causing your car not to start. Contact a Peugeot specialist, or a locksmith, if this is the situation.
Another issue that is common is when the key fob battery is dying, this causes the key blade to stop feeding into the lock. A locksmith for cars can replace the battery and cut a fresh blade for you, this is typically a quick fix.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, or being exposed to a sudden rain or accidentally washing it may be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which manages the central locking system of your Peugeot vehicle.
The key fob itself has rubber seals that block water from reaching the electronic chip inside. However prolonged exposure to water may penetrate these seals and damage the chip. Submerging the key fob in sea water at the beach or throwing it into the pool could be particularly damaging due to the high salt content.
If your Peugeot spare key fob isn't working You'll need the module replaced. This can only be performed by a professional auto locksmith or Peugeot specialist. As opposed to other cars, Peugeot keys are protected by an exclusive immobilizer system that requires the correct coding to begin the engine. This is why you should choose a reputable Peugeot locksmith to take on the job of designing and programming an appropriate replacement.
Computer on board is not working properly
The on-board computer of your Peugeot is responsible for many of the systems in your car, including airbags and power windows. The on-board computer will display a code if something goes wrong. This code will be saved in the system until the issue is fixed. Most often, this involves replacing the computer on board.
The most typical reason for the warning light for the airbag to flash is corrosion or loose connections in the sensor. This can occur due to wear and tear, aging or exposure to salt and moisture. It is imperative to have this issue resolved as soon as possible, since a malfunctioning airbag can be dangerous in the event an accident.
If your Peugeot is showing a card that is not being detected error, the battery inside the key fob may be weak or dead. This will stop the key fob from sending a signal to disarm the vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then trying to start your vehicle. If this fails, the key battery needs to be replaced.